TM 9-2320-266-34
Table 1-2. Torque Specifications-Continued
Table 1-2. Torque Specifications-Continued
Ft-lbs In-lbs
Location
Ft-lbs In.lbs
Location
SUSPENSION
TRANSFER CASE-Continued
Axle housing cover
20
Rear out put bearing retainer assembly
Ball joint nuts (4X2)
bolts
30
Lower
135
Output shaft yoke nuts
120
Upper
135
Lockout shift poppet plug
20
Brake support to steering knuckle
Range shift poppet plug
20
4X2
215
Power takeoff cover bolts
15
4x4
35
Shifter assembly to adapter bolts
30
Companion flange nut (4X4)
210
Shift lever to shifter assembly nut
30
Differential carrier cap (4X4)
80
Knob assembly jam nut
10
Propeller shaft clamping screws
14
170
Range and locknut shift lever locknut
20
Shock absorber lower mounting
Shift rod swivel clamp screw
11
200
4X2
Filler plug
17
30
4x4
55
TRANSMISSION
Steering links (4X4)
47
9
Strut front mounting (4X2)
110
50
Cooler line fitting
Strut rear mounting (4X2)
85
Cooler line nut
85
Tie rod clamping bolt (4X2)
13
160
Converter drain plug
90
Tie rod end nuts
55
Converter drive plate to crankshaft bolt
4X2
40
Converter drive plate to torque conver-
60
4x4
ter bolt
23
270
Upper control arm mounting (4X2)
70
Extension housing to transmission case
Lower control arm mounting (4X2)
210
bolt
24
Extension housing to insulator mounting
STEERING GEAR
50
bolt
Worm bearing preload adjuster locknut
85
Governor body to support bolt
8
100
Side cover bolts
30
35
Kickdown band adjusting screw locknut
Sector shaft adjusting screw locknut
25
Kickdown lever shaft plug
13
150
Coupling flange bolts
30
Neutral safety switch
24
Coupling flange nuts
25
Oil pan bolt
13
150
30
Wormshaft clamp bolt
Oil pump housing to transmission case
180
Steering gear arm nut
15
bolt
175
Gear to frame bolts
50
Output shaft support bolt
13
150
Overruling clutch cam set screw
3
40
TRANSFER CASE
Pressure test take-off plug
9
110
31
Adapter to transmission attaching bolt
Reaction shaft support to oil pump bolt
13
160
30
Adapter to transfer case attaching bolts
Reverse band adjusting screw locknut
30
30
Range box to chain case
Speedometer drive clamp screw
8
100
30
Differential housing to chain case
Transmission to engine bolt
28
20
Front input bearing retainer bolts
Valve body screw
35
3
30
Front output front bearing retainer bolts
Valve body to transmission case, bolt
100
8
30
Front output rear bearing retainer bolts
55
Differential carrier bolt
1-11. Radio Interference.
a. Some M880-series vehicles have military radio suppres-
sion componentry (table 1-3). The parts that are affected by
NOTE
this are:
The M880, M886, M890, and M893 trucks
Starter relay capacitor
are not equipped with military standard
Distributor cap
electro-magnetic interference components,
Distributor rotor
although they do contain commercial
Spark plug shields
standard SAE suppression componentry,
Ignition coil shield
They should not be operated within
Spark plug and ignition coil cables
50 feet of a vehicle with communications
Voltage limiter
equipment or any ground receiver/trans-
Fender shields
mitter. The unsuppressed vehicles may
Ground strap
interfere with operation of the communi-
Windshield wiper motor
cations equipment,
Heater motor
1-6
Change 2
