TM 9-2320-289-20P
sequence. The NIIN consists of the last nine
NSN
digits of the NSN (i.e.,
When
I
NIIN
using this column to locate an item, ignore the first 4 dig-
its of the NSN. However, the complete NSN should be
used when ordering items by stock number.
(2) FIG. column. This column lists the number of
the figure where the item is identified/located. The fig-
ures are in numerical order in Section II and Section Ill.
(3) ITEM column. The item number identifies the
item associated with the figure listed in the adjacent
FIG. column. This item is also identified by the NSN
listed on the same line.
b. PART NUMBER INDEX. Part numbers in this index
are listed by part number in ascending alphanumeric
sequence (i.e., vertical arrangement of letter and
number combination which places the first letter or digit
of each group in order A through Z, followed by the
numbers O through 9 and each following letter or digit in
like order).
(1) CAGEC column. The Commercial and Gov-
ernment Entity (CAGE) Code (C) is a 5-digit
alphanumeric code used to identify the manufacturer,
distributor, or Government agency, etc., that supplies
the item.
(2) PART NUMBER column. Indicates the pri-
mary number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the
design and characteristics of the item by means of its
engineering drawings, specifications standards, and in-
spection requirements to identify an item or range of
items.
(3) STOCK NUMBER column. This column lists
the NSN for the associated part number and manufac-
turer identified in the PART NUMBER and CAGE
columns to the left.
(4) FIG. column. This column Iists the number of
the figure where the item is identified/located in Sec-
tions II and Ill.
(5) ITEM column. The item number is that num-
ber assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
c. FIGURE AND ITEM NUMBER INDEX.
(1) FIG. column. This column lists the number of
the figure where the item is identified/located in Sec-
tions II and Ill.
(2) ITEM column. The item number is that num-
ber assigned to the item as it appears in the figure
referenced in the adjacent figure number column.
5305-01-674-1467).
(3) STOCK NUMBER column. This column lists
the NSN for the item.
(4) CAGEC column. The Commercial and Gov-
ernment Entity (CAGE) Code (C) is a 5-digit alpha-
numeric code used to identify the manufacturer, distribu-
tor, or Government agency, etc., that supplies the item.
(5) PART NUMBER column. Indicates the pri-
mary number used by the manufacturer (individual, firm,
corporation, or Government activity), which controls the
design and characteristics of the item by means of its
engineering drawings, specifications standards and in-
spection requirements to identify an item or range of
items.
5. Special Information.
a. USABLE ON CODE. The usable on code appears
in the lower left comer of the Description column
heading. Usable on codes are shown as “UOC: . . . . . . “
in the Description column (justified left) on the first line
following applicable item description/nomenclature.
Uncoded items are applicable to all models.
Identification of the usable on codes used in the RPSTL
are:
Code
Used On
194
M1008,Type “B’’Cargo,
Shelter
208
M1008A1, Type “B”
Cargo, Troop Seat
209
M1009, Type “A” Utility
210
M1010, Type “C”
Ambulance
230
Ml 028, Type “E” Shelter
Carrier
252
M1028A1, Type”F”
Shelter Carrier w/PTO
254
M1028A2, Type “F”
Shelter Carrier w/PTO
256
M1028A3, Type “E
Shelter Carrier
231
M1031, Type “D”
Chassis
b. FABRICATION INSTRUCTIONS. Bulk materials
required to manufacture items are listed in the Bulk
Material Functional Group of this RPSTL. Part numbers
for bulk materials are also referenced in the Description
column of the line item entry for the item to be
manufactured/fabricated.
Detailed
fabrication
instructions for items source coded to be manufactured
or fabricated are found in TM 9-2320-28920 or TM 9-
2320-289-34.
c. ASSEMBLY INSTRUCTIONS. Detailed assembly
instructions for items source coded to be assembled
---
4
